2lb. Flotation and Insulation Foam – 2 Gallon Kit

$139.00

Same Day Shipping: Orders Placed Before 2pm PT M-F

Canadian Customers click here for shipping details.

AeroMarine Products 2# density polyurethane pour foam. Designed for positive flotation, cavity and void fills, and insulation. 2 gallon kit; includes one gallon each of Part A and Part B.

DESCRIPTION
HOW-TO
FAQS
SHIPPING & RETURNS
PURCHASE NOW
TDS

PRODUCT DESCRIPTION

Features

Low viscosity
Convenient volumetric mix ratio (1:1)
Rapid set time
Low odor
Excellent base for epoxy/polyester resins
Readily accepts paints, stains and finishes
Approvable under U.S. Coast Guard Regulation # 33 CFR 183.114

Physical Properties:

Parallel to Rise Compressive Strength: 40 psi
Tensile Strength: 30 psi
Shear Strength: 30 psi
Flexural Strength: 50 psi

Room Temperature Features of Resultant Product

Cured Density: 2 lbs/ cubic foot
Compressive strength: 40 psi
K-factor: 0.22
R- Value: 7 per inch

HOW-TO

Mixing

2 lbs. pour-in-place urethane foam is mixed in a 1:1 ratio.
Mix only small amounts at a time (minimum mixture volume of 3 ounces and maximum of ½ gallon amounts of Part A and Part B for total of 1 gallon and wait at least 30 minutes between pours.
Mixing time is approximately 20 -30 seconds.
Working time is one minute.
The 2 lbs. pour foam will fill about one cubic foot per quart of mixed liquid at 72 F.
If the foam is mixed at a lower temperature, it will NOT expand to its maximum capacity.
If it is hotter than 72F, the 2 lbs. foam may expand very quickly and prevent a consistent expansion.
Always mix pour foam in clean plastic containers with clean plastic or metal mixing tools.
- Do not use a wax, paper or wood container or mixing tools because these materials contain moisture which will contaminate the foam!

Clean Up:

The “A” part of the foam cleans up with acetone and the “B” part with water.
Due to the adhesive quality of the foam, keep the mixed product off everything except the job itself.

Tips

Everything (foam, tools, containers and ambient temperature) must be at 72F before you start using the foam.
If your work space is colder than 72F, please keep the foam containers off the floor.
Pour foam is very sensitive to humidity.
Humidity causes air bubble which result in a poor quality cured foam.
- Do everything possible to avoid getting moisture into the foam.
- This includes replacing the lids on containers immediately after use as well as not using pour foam on rainy and/or high humidity days.
Shake Part “B” well for 30 seconds before pouring.
Only mix small quantities of Part “A” and Part “B” at one time.
Do not vary the mix ratio with pour foam.
Do not use a drill to mix pour foam as it will result in premature curing and air bubbles.
Heat the cavity the foam is to be poured into, if it is cold to the touch.
Always wear a respirator or self –contained breathing apparatus and gloves when working with pour foam (A paper painter’s mask is not sufficient!)
Do NOT spray! This is NOT a sprayable foam.
Do NOT use with inflatables and/or canvas
Never mix less than 3 ounces of pour foam, as this quantity is difficult to achieve the correct ratio and will not generate enough heat to cure the pour foam properly.

FAQs

Q. What is the largest cavity I could fill with the 2# 2 gallon pour foam kit?

A cavity with a calculated volume of 8 cubic feet, which is equivalent to a single 55 gallon drum.

Q. What is the largest cavity I could fill with the 2# 1/2 gallon pour foam kit?

A cavity with a volume of 2 cubic feet calculated Width x Length x Height or for cylindrical shapes; πr2x height
Where π= 3.14 and r = diameter x 1/2
If you did the math in inches, divide the final answer by 1,728 to get the cubic footage.

Q. Does AeroMarine offer other sizes besides the ½ gallon 2# pour foam kit?

Yes, AeroMarine also offers 2 gallon, 10 gallon, and 110 gallon kits depending on your project.

Technical Data Sheets (TDS)

Download

SHIPPING AND RETURNS

Shipping
Via UPS Ground

Returns
We only accept returns of unopened and unused product. Customer must return product within 30 days of receipt. Customer must contact us before returning a product. Customer pays for return shipping. All returns are charged a 15% restocking fee.

**shipping estimates may vary based on product selection and destination and a tracking code will be sent after checkout.

Canadian Customers**

If you are ordering from Canada, additional shipping rates and fees may apply. Please contact one of our representatives for more information. Contact us today!

Featured Products

Shop by Project

Shop by Color

Accessories & Guides

Featured Products

Shop by Project

Shop by Color

Featured Products

Shop by Project

Shop by Type

Accessories & Guides

Featured Products

Shop by Project

Shop by Type

Accessories and Guides

Featured Products

Shop by Project

Shop by Color

Accessories & Guides

Featured Products

Shop by Project

Shop by Material

Shop by Color

Featured Products

Shop by Project

Calculators

2lb. Flotation and Insulation Foam – 2 Gallon Kit

Canadian Customers**